350-601: Implementing and Operating Cisco Data Center Core Technologies (DCCOR)

Question #: 61
Topic #: 1
A Cisco ACI engineer must configure an access port on a Cisco ACI leaf switch. The access policy should be configured so that it supports L3Out connectivity concurrently with several EPGs that are mapped to this interface with the static port method. How should the access policy be configured?

A. by linking the interface policy group to multiple Attachable Access Entity Profiles
B. with two interface policy groups that are linked to the same interface profile port selector
C. by mapping a single physical domain, mapped to the L3out and EPG interfaces
D. with a single Attachable Access Entity Profile that is linked to the corresponding routed domain and physical domain

Selected Answer: D

Question #: 62
Topic #: 1
Refer to the exhibit. An engineer monitors ingress traffic from Host-A and all traffic for VLAN 20 from Host-B. Which configuration must be implemented to monitor and export traffic to Network Analyzer?

A. SW-1(config)# monitor session 5 SW-1(config-monitor)# source interface ethernet 1/2 rx SW-1(config-monitor)# source interface ethernet 1/1 tx SW-1(config-monitor)# source vlan 20 both SW-1(config-monitor)# destination ip 10.10.10.1 SW-1(config-monitor)# no shut
B. SW-1(config)# monitor session 5 type erspan-source SW-1(config-erspan-src)# source interface ethernet 1/2 rx SW-1(config-erspan-src)# source vlan 20 both SW-1(config-erspan-src)# destination ip 10.10.10.1 SW-1(config-erspan-src)# erspan-id 111 SW-1(config-erspan-src)# no shut
C. SW-1(config)# monitor session 5 SW-1(config-monitor)# source interface ethernet 1/2 rx SW-1(config-monitor)# source interface ethernet 1/1 both SW-1(config-monitor)# source vlan 20 both SW-1(config-monitor)# destination interface ethernet 2/1 SW-1(config-monitor)# no shut
D. SW-1(config)# monitor session 5 type erspan SW-1(config-erspan-src)# source interface ethernet 1/2 rx SW-1(config-erspan-src)# source interface ethernet 1/1 both SW-1(config-erspan-src)# destination ip 10.10.10.1 SW-1(config-erspan-src)# mtu 1000 SW-1(config-erspan-src)# no shut

Selected Answer: B

Question #: 63
Topic #: 1
Refer to the exhibit. Which action completes the vPC domain implementation?

A. Add the vPC member ports to the vPC channel group.
B. Configure the system MAC on the vPC domain.
C. Include the VRF management on the vPC domain.
D. Allow VLANs on the vPC peer link member interfaces.

Selected Answer: A

Question #: 64
Topic #: 1
Refer to the exhibit. A network engineer is implementing a configuration checkpoint on a Cisco Nexus 9000 Series Switch. The configuration must skip any existing vPC configuration errors and must complete if there are any configuration errors. The engineer finished the vPC domain configuration part. Which command completes the checkpoint implementation?

A. best-effort
B. stop-at-first-failure
C. atomic
D. verbose

Selected Answer: A

Question #: 65
Topic #: 1
An engineer must implement a VXLAN-based data center interconnect. The long-distance transport provided by a service provider is IP-based, supports a maximum MTU of 1554 bytes, and does not support outbound traffic replication. Which action must be taken to build the data center interconnect?

A. Announce host reachability over BGP.
B. Create an IP access list and associate it with VNI to replicate traffic to remote VTEPs.
C. Configure a route map to associate the IPs of the remote VTEPs.
D. Implement BGP EVPN ingress replication.

Selected Answer: D

Question #: 66
Topic #: 1
An engineer must perform an initial configuration of VXLAN Tunnel End-Point functionality on the Cisco Nexus 9000 Series platform. All the necessary features are already enabled on the switch. Which configuration set must be used to accomplish this goal?

A. NX9K(config)# interface loopback0 NX9K(config-if)# ip address 10.10.10.11/32 NX9K(config)# interface VLAN10 NX9K(config-if)# ip unnumbered loopback0 NX9K(config)# interface nve1 NX9K(contig-if-nve)# source-interface loopback0
B. NX9K(config)# interface loopback0 NX9K(config-if)# ip address 10.10.10.11/32 NX9K(config)# interface overlay0 NX9K(config-if-overlay)# source-interface loopback0 NX9K(config)# interface VLAN10 NX9K(contig-if-nve)# source-interface loopback0
C. NX9K(config)# interface loopback0 NX9K(config-if)# ip address 10.10.10.11/32 NX9K(config)# interface tunnel1 NX9K(config-if)# tunnel source loopback0 NX9K(config)# interface ethernet1/1 NX9K(contig-if)# ip unnumbered loopback0
D. NX9K(config)# interface loopback0 NX9K(config-if)# ip address 10.10.10.11/32 NX9K(config)# interface nve1 NX9K(config-if-nve)# source-interface loopback0 NX9K(config)# interface ethernet1/1 NX9K(contig-if)# ip unnumbered loopback0

Selected Answer: D

Question #: 67
Topic #: 1
An engineer must perform a software upgrade on a production Cisco Nexus 7000 Series Switch. Before the upgrade activity, the requirement is for all ports to be shut down and routing protocols to terminate gracefully. Which feature must be used to meet these requirements?

A. Switch Profile
B. Service Profile Template
C. Maintenance Mode Profile
D. Configuration Profile

Selected Answer: C

Question #: 68
Topic #: 1
DRAG DROP –

Refer to the exhibit. An engineer must monitor the Ethernet port and the corresponding VLAN traffic for the hyper4 device. The SW3 device is a Cisco Nexus 7000
Series Switch. Drag and drop the code snippets from the right into the boxes in the configuration to meet these requirements.
Select and Place:

Suggestion Answer:

Question #: 69
Topic #: 1
DRAG DROP –
Drag and drop the network assurance concepts from the left onto the corresponding benefits on the right.
Select and Place:

Suggestion Answer:

Question #: 70
Topic #: 1
DRAG DROP –
An engineer must configure HSPR protocol on two Cisco Nexus 9000 Series Switches running a virtual port channel. In addition, the HSRP implementation must meet these requirements:
✑ It must allow more than 500 groups.
✑ switch1 must act as the primary switch.
✑ Both switches must use a user-defined hardware address.
Drag and drop the commands from the right to complete a configuration of the HSRP on the left. The commands are used more than once. Not all commands are used.
Select and Place:

Suggestion Answer:

Question #: 71
Topic #: 1
An engineer must configure OSPFv2 connectivity between a pair of Cisco Nexus switches. The connection between the switches must meet these requirements:
✑ Use unicast for updates.
✑ Use decentralized communication of updates.
✑ Full adjacency between switches.
Which configuration is needed to meet these requirements?

A. filter list between the neighbors
B. stub area between the neighbors
C. virtual link between the neighbors
D. interface with a type of p2p network

Selected Answer: C

Question #: 72
Topic #: 1
An infrastructure architect is analyzing the deployment type for an application. Several companies must be able to operate the application environment and integrate it with a third-party protocol. The development team also must have maximum control over their development environment, including the operating system used, Python interpreter, and corresponding libraries. Which cloud deployment solution meets these requirements?

A. private cloud Platform as a Service
B. public cloud Storage as a Service
C. hybrid cloud Software as a Service
D. community cloud Infrastructure as a Service

Selected Answer: D

Question #: 73
Topic #: 1
An engineer is performing an ISSU upgrade on the Cisco MDS 9000 Series Switch. What is the impact on the control plane of the switch?

A. It is down for less than 80 seconds.
B. It remains down for more than 80 seconds but less than 140 seconds.
C. It remains down until the next reboot.
D. It remains up throughout the update.

Selected Answer: A

Question #: 74
Topic #: 1
An engineer must implement a disaster recovery policy for the Cisco UCS infrastructure. The solution must meet these criteria:
✑ The Recovery Point Objective must be 48 hours.
✑ The backup must use encrypted transmission.
The Recovery Time Objective must be 4 hours.

Which configuration set must be used in the scheduled backup to meet these requirements?

A. Protocol: FTP Schedule: Bi-Weekly
B. Protocol: SFTP Schedule: Weekly
C. Protocol: TFTP Schedule: Bi-Weekly
D. Protocol: SCP Schedule: Daily

Selected Answer: D

Question #: 75
Topic #: 1
Refer to the exhibit. What happens to the broadcast traffic when it reaches aggregation switches?

A. Agg-2 switch receives broadcast packets and stops forwarding to the peer link on Agg-1 switch.
B. Agg-1 switch prevents broadcast packets received on the vPC peer link from exiting the switch on ports Eth2/4 and Eth2/5.
C. Agg-1 and Agg-2 switches receive broadcast packets and does not forward them to the peer link or the port channel.
D. Only Agg-1 switch receives broadcast packets and does not forward to the peer link on Agg-2 switch.

Selected Answer: B

Question #: 76
Topic #: 1
Which feature is supported with an In-Service Software Upgrade on a Cisco Nexus 9000 Series Switch?

A. nondisruptive upgrades via nonstop forwarding
B. configuration changes during an upgrade
C. upgrades to individual modules and line cards
D. zero downtime downgrades via dual supervisor modules

Selected Answer: A

Question #: 77
Topic #: 1
An engineer must configure a monitoring solution for a Cisco Nexus 9000 Series Switch based data center. The solution must provide real-time insight into the network health with subscription-based monitoring. The monitoring must be initiated from the client side, and the data must be sent via encryption. Which configuration steps complete the configuration?

A. Configure Grafana on the Nexus switch. Specify the logging certificate. Enable syslog level 7 export to Grafana.
B. Set the telemetry feature on the Nexus switch. Specify a certificate for telemetry transport. Configure a sensor group and destination.
C. Activate SNMPv3 on the Nexus switch. Set the globalEnforcePriv parameter. Configure an SNMP agent to poll information.
D. Enable GRPC on the Nexus switch. Generate a certificate. Configure gNMI inputs in Telegraf and output to InfluxDB.

Selected Answer: B

Question #: 78
Topic #: 1
Refer to the exhibit. Software downgrade is required on a Cisco Nexus 7000 Series Switch. What is displayed when this command is executed?

A. features that are enabled automatically after the downgrade
B. impact of a software upgrade in ISSU and chassis reload
C. features and commands that are removed automatically from the configuration
D. compatibility of software in the system bootflash file

Selected Answer: C

Question #: 79
Topic #: 1
The VMM domain is integrated between Cisco APICs and vCenter using a distributed vSwitch. The traffic must be blocked between a subset of endpoints in an
EPG based on specific VM attributes and the rest of the VMs in that EPG. Which set of actions blocks this traffic?

A. 1. Set Allow Microsegmentation under the EPG VMM Domain Association to ג€Trueג€ 2. Set Intra-EPG Isolation to ג€Unenforcedג€ for the EPG 3. Set Intra-EPG Isolation to ג€Unenforcedג€ for the uSeg EPG
B. 1. Set Allow Microsegmentation under the EPG VMM Domain Association to ג€Falseג€ 2. Set Intra-EPG Isolation to ג€Unenforcedג€ for the EPG 3. Set Intra-EPG Isolation to ג€Enforcedג€ for the uSeg EPG
C. 1. Set Allow Microsegmentation under the EPG VMM Domain Association to ג€Trueג€ 2. Set Intra-EPG Isolation to ג€Enforcedג€ for the EPG 3. Set Intra-EPG Isolation to ג€Enforcedג€ for the uSeg EPG
D. 1. Set Allow Microsegmentation under the EPG VMM Domain Association to ג€Trueג€ 2. Set Intra-EPG Isolation to ג€Enforcedג€ for the EPG 3. Set Intra-EPG Isolation to ג€Unenforcedג€ for the uSeg EPG

Selected Answer: C

Question #: 80
Topic #: 1
DRAG DROP –
Drag and drop the firmware packages from the left onto the software bundles they belong to on the right.
Select and Place:

Suggestion Answer:

Question #: 81
Topic #: 1
Which action must be performed before renumbering a Cisco UCS chassis?

A. Run the shut and no shut command on the connected ports.
B. Move the chassis to new ports on fabric interconnect.
C. Decommission the chassis.
D. Re-acknowledge the chassis.

Selected Answer: C

Question #: 82
Topic #: 1
A server engineer wants to control power usage on a Cisco UCS C-Series rack server down to the component level.
Which two components support specific power limits? (Choose two.)

A. storage controller
B. network controller
C. processor
D. graphic card
E. memory

Selected Answer: AB

Question #: 83
Topic #: 1
An engineer is implementing an import operation in Cisco UCS Manager.
What is the impact of performing this operation?

A. Information is modified on the management plane only.
B. A configuration is imported from a higher release to a lower release.
C. It is possible to schedule an import operation.
D. Only a configuration file that was exported from the same Cisco UCS Manager is allowed to be imported.

Selected Answer: A

Question #: 84
Topic #: 1
An engineer wants to create a backup of Cisco UCS Manager for disaster recovery purposes.
What are two characteristics of a full state backup of a Cisco UCS Manager database? (Choose two.)

A. contains all of the runtime states and statuses but not the configurations
B. performs a complete binary dump of the database as a .bin file
C. performs a complete binary dump of the database as a .sql file
D. performs a complete binary dump of the database as a .txz file
E. contains all of the configurations

Selected Answer: BE

Question #: 85
Topic #: 1
What happens to the default host firmware policy after a Cisco UCS Manager upgrade?

A. It is assigned to all the service profiles that include a host firmware policy.
B. It is replaced by a new default policy without any firmware entries.
C. It is set to match the host firmware policy.
D. It is updated to contain the firmware entries of all the components.

Selected Answer: A

Question #: 86
Topic #: 1
An engineer is asked to use SaaS to manage Cisco computing.
Which two items are needed to accomplish the task? (Choose two.)

A. Intersight
B. UCS Central
C. Device/Claim ID
D. Node name/Serial Number
E. UCS Manager

Selected Answer: AC

Question #: 87
Topic #: 1
An engineer is configuring a backup operation on the existing Cisco UCS environment using a logical configuration.
Which configuration is expected to be saved by using this backup type?

A. systems
B. roles
C. servers
D. service profiles

Selected Answer: D

Question #: 88
Topic #: 1
An engineer is seeking the most optimal on demand CPU performance while configuring the BIOS settings of a UCS C-series rack mount server.
What setting will accomplish this goal?

A. C6 Retention
B. C6 non-Retention
C. C2 state
D. C0/C1 state

Selected Answer: A

Question #: 89
Topic #: 1
An engineer is duplicating an existing Cisco UCS setup at a new site.
What are two characteristics of a logical configuration backup of a Cisco UCS Manager database? (Choose two.)

A. contains the configured organizations and locales
B. contains the VLAN and VSAN configurations
C. contains the AAA and RBAC configurations
D. contains all of the configurations
E. contains a file with an extension.tgz that stores all of the configurations

Selected Answer: BC

Question #: 90
Topic #: 1
Refer to the exhibit.

Which two Cisco UCS components are upgraded as a result of the configuration? (Choose two.)

A. IOMs
B. Cisco UCS Manager
C. board controller
D. adapters
E. BIOS

Selected Answer: AB

Question #: 91
Topic #: 1
Which two settings must be configured before enabling a Cisco UCS Manager domain for Cisco Intersight connectivity? (Choose two.)

A. SMTP servers
B. SMTP reply-to address
C. NTP servers
D. syslog redirection
E. DNS servers

Selected Answer: CE

Question #: 92
Topic #: 1
An engineer must configure Cisco IMC server management NIC for autonegotiation.
Which setting should be selected?

A. shared LOM
B. Cisco card
C. dedicated
D. shared LOM EXT

Selected Answer: C

Question #: 93
Topic #: 1
A network engineer is adding a Cisco HyperFlex data platform to the Cisco Intersight management portal.
Which two components are required for Intersight to claim the Cisco HyperFlex data platform? (Choose two.)

A. device FQDN
B. device claim code
C. device public IP address
D. device ID
E. device serial number

Selected Answer: BD

Question #: 94
Topic #: 1
Where is the witness deployed in a two-node Cisco HyperFlex Edge deployment?

A. to the HyperFlex Edge two-node cluster
B. to Cisco Intersight
C. to a third-party cloud provider
D. to an additional server with network access to HyperFlex Edge

Selected Answer: B

Question #: 95
Topic #: 1
Refer to the exhibit.

What is the result of this series of commands?

A. It reboots the server immediately.
B. It activates the firmware on the next adapter boot.
C. It updates the firmware on adapter 1/1/1 immediately.
D. It verifies the firmware update on the server.

Selected Answer: B

Question #: 96
Topic #: 1
What is the benefit of adding Cisco HyperFlex Hardware Acceleration Cards to a HyperFlex deployment?

A. increased compression efficiency
B. increased network throughput
C. GPU acceleration
D. offline encryption acceleration

Selected Answer: A

Question #: 97
Topic #: 1
When the default firmware package is set to a new version, which type of policy determines the timing of server reboots during the firmware upgrade?

A. diagnostics
B. maintenance
C. local disk
D. BIOS

Selected Answer: B

Question #: 98
Topic #: 1
Which two hypervisors does Cisco HyperFlex support? (Choose two.)

A. OpenStack
B. Citrix XenServer
C. VMware vSphere
D. RedHat KVM
E. Microsoft Hyper-V

Selected Answer: CE

Question #: 99
Topic #: 1
DRAG DROP –
An engineer deploys a custom guest shell rootfs onto multiple switches.
Drag and drop the steps from the left into the correct order on the right.
Select and Place:

Suggestion Answer:

Question #: 100
Topic #: 1
An engineer changed a configuration and must perform a rollback.
Which statement applies to a Cisco Nexus 5600 Series Switch?

A. The configuration rollback functionality is disabled when FCoE is enabled.
B. A system checkpoint is generated automatically when the running configuration is saved to NVRAM.
C. A user who is assigned to the network-operator user role is allowed to perform a rollback.
D. Errors are skipped when an atomic rollback type is triggered.

Selected Answer: A

Question #: 101
Topic #: 1
Which statement describes the rolling EPLD upgrade on a Cisco MDS 9000 Series Switch?

A. The standby supervisor module is capable of performing the upgrade.
B. Only the modules that are being upgraded are disrupted.
C. All modules on the switch are disrupted.
D. An EPLD upgrade is nondisruptive.

Selected Answer: B

Question #: 102
Topic #: 1
Which command reduces the amount of time it takes to complete the ISSU on a Cisco Nexus 7000 Series Switch that has dual supervisor modules and two I/O modules?

A. insinstall all epld bootflash: parallel
B. install all kickstart  system  parallel
C. install all kickstart  system 
D. install all epld bootflash: 

Selected Answer: B

Question #: 103
Topic #: 1
Which two statements describe the process of performing an EPLD upgrade on a Cisco MDS 9000 Series Switch? (Choose two.)

A. The upgrade is performed from the standby supervisor module.
B. The upgrade process disrupts only the module that is being upgraded.
C. The upgrade is performed on the active supervisor.
D. If an upgrade is interrupted, the upgrade continues after a connection is restored.
E. Modules must be online to be upgraded.

Selected Answer: BE

Question #: 104
Topic #: 1
Which two statements describe the process of upgrading an EPLD on a Cisco MDS 9000 Series Switch? (Choose two.)

A. EPLDs are only capable to be upgraded to the latest EPLD image.
B. EPLD upgrades are capable to be completed without powering down the module during the upgrade.
C. An upgrade verification identifies the impact of each EPLD upgrade.
D. The EPLDs for all the modules on a switch must be upgraded at the same time.
E. EPLDs are capable to be upgraded without replacing the hardware.

Selected Answer: CE

Question #: 105
Topic #: 1
Refer to the exhibit.

What is the outcome of this command when the EPLD is updated on a Cisco Nexus 9000 Series Switch?

A. displays the compatibility of the EPLD upgrade and the image in the bootflash
B. shows a simulated upgrade of the EPLD
C. upgrades the EPLD on the switch disruptively
D. displays the impact of the upgrade on the operation of the switch

Selected Answer: D

Question #: 106
Topic #: 1
DRAG DROP –
An engineer is configuring VNTag between a virtualized server and a Cisco Nexus 5500 Series switch.
Drag and drop the configuration steps from the left into the correct order on the right.
Select and Place:

Suggestion Answer:

Question #: 107
Topic #: 1
Multiple roles are applied to a user on the Cisco MDS 9000 Series Switch.
Which statement describes the result of this configuration?

A. The last role assigned takes precedence over previous roles.
B. Access to a command takes priority over being denied access to a command.
C. Any commands that have conflicting settings between roles are denied.
D. The first role assigned takes precedence over subsequent roles.

Selected Answer: B

Question #: 108
Topic #: 1
Refer to the exhibit.

Which backup operation type does not include the Preserve Identities feature?

A. full state
B. all configuration
C. logical configuration
D. system configuration

Selected Answer: A

Question #: 109
Topic #: 1
Refer to the exhibit.

What is a characteristic presented in the service profile of the UUID?

A. unique system generated
B. allocated from a UUID pool
C. vendor assigned
D. based on the hardware

Selected Answer: B

Question #: 110
Topic #: 1
Refer to the exhibit.

Which action must be taken before the maintenance policy can be committed?

A. Specify a maintenance time by selecting a schedule.
B. Associate a service profile to the maintenance policy.
C. Set the soft shutdown timer to a specific time.
D. Set the policy to apply the changes on the next reboot.

Selected Answer: A

Question #: 111
Topic #: 1
Which two firmware packages are included in the Cisco UCS C-Series Rack-Mount UCS-Managed Server Software bundle? (Choose two.)

A. CIMC
B. BIOS
C. PSU
D. system
E. third-party

Selected Answer: AB

Question #: 112
Topic #: 1
A UCS B-Series server located in B5108 chassis 1 slot 1 is currently unavailable. The server needs to be associated with a specific service profile when it becomes available. Which associate service profile option should be selected to accomplish this goal?

A. restrict migration
B. server pool
C. server
D. custom server

Selected Answer: D

Question #: 113
Topic #: 1
A Cisco UCS C-Series server is installed at a data center. The server should be managed by the Cisco UCS Manager by using a single cable for management and data traffic. Which configuration should be applied after the physical connection is established?

A. UCS-A# scope server 1 UCS-A /server# scope cimc UCS-A /server/cimc # scope mgmt-conn sideband UCS-A /server/cimc # mgmt-conn-state enabled UCS-A /server/cimc/mgmt-conn* # commit-buffer
B. UCS-A# scope chassis 1 UCS-A /chassis# scope cimc UCS-A /chassis/cimc # scope mgmt-conn sideband UCS-A /chassis/cimc/mgmt-conn # mgmt-conn-state enabled UCS-A /chassis/cimc/mgmt-conn* # commit-buffer
C. UCS-A# scope chassis 1 UCS-A /chassis# scope cimc UCS-A /chassis /cimc # set mgmt-conn-state enabled UCS-A /chassis /cimc/mgmt-conn* # commit-buffer
D. UCS-A# scope server 1 UCS-A /server# scope cimc UCS-A /server/cimc # scope mgmt-conn sideband UCS-A /server/cimc/mgmt-conn #set mgmt-conn-state enabled UCS-A /server/cimc/mgmt-conn* # commit-buffer

Selected Answer: D

Question #: 114
Topic #: 1
Refer to the exhibit. Which type of backup is required to restore a Cisco UCS configuration?

A. system configuration
B. all configuration
C. full state
D. logical configuration

Selected Answer: C

Question #: 115
Topic #: 1
Which server policy is used to install new Cisco IMC software on a server?

A. hypervisor firmware policy
B. host firmware policy
C. BIOS software policy
D. Cisco IMC software policy

Selected Answer: C

Question #: 116
Topic #: 1
What are two requirements when planning a Cisco HyperFlex All Flash standard cluster installation using three Cisco HX240c M5 Series servers? (Choose two.)

A. If the Jumbo MTU option in the HyperFlex installer is enabled, then jumbo frames do not have to be enabled on the upstream switches.
B. This cluster deployment type must support a mix of HDD and SSD.
C. The servers must be discovered, unassociated, and connected to each fabric interconnect.
D. If the Jumbo MTU option in the HyperFlex installer is enabled, then jumbo frames must also be enabled on the upstream switches.
E. The hypervisors must be installed to Cisco FlexFlash SD cards.

Selected Answer: CD

Question #: 117
Topic #: 1
Refer to the exhibit. Service degradation is reported on a VM that is deployed on a Cisco UCS B-Series Server. The traffic from the vNIC is required to SPAN in both directions to a packet analyzer that is connected to UCS-A slot 2 port 12. Which two commands are needed to complete the configuration? (Choose two.)

A. UCS-A /org/service-profile/vnic/mon-src* # set direction receive transmit
B. UCS-A /eth-traffic-mon/fabric/eth-mon-session* # create dest-interface 2 12
C. UCS-A /eth-traffic-mon/fabric/eth-mon-session # activate
D. UCS-A /eth-traffic-mon/fabric/eth-mon-session* # create eth-mon-session/dest-interface 2 12
E. UCS-A /org/service-profile/vnic/mon-src* # set direction both

Selected Answer: BE

Question #: 118
Topic #: 1
An engineer updated firmware on Fabric Interconnects and activates it. However, the endpoint fails to boot from the new firmware image. What is expected to occur in this case?

A. The system defaults to and boots into kickstart image
B. The system defaults to and boots into GOLD firmware image
C. The system defaults to the GOLD firmware image
D. The system defaults to the backup image version

Selected Answer: D

Question #: 119
Topic #: 1
Which service profile is affected if the default host firmware policy in Cisco UCS Manager is changed?

A. any service profile that uses the global-default host firmware policy
B. any service profile that uses a user-created host firmware policy
C. any service profile that has no host firmware policy defined
D. any service profile that is not in the root sub-org

Selected Answer: C

Question #: 120
Topic #: 1
An engineer is implementing Cisco Intersight in a secure environment. The environment must use LDAP directory service and ensure information integrity and confidentiality. Which two steps must be taken to implement the solution? (Choose two.)

A. Enable Certificate Signing Request in Cisco Intersight
B. Add a trusted root LDAP certificate to Cisco Intersight
C. Enable Encryption for LDAP
D. Add a self-signed LDAP certificate to Cisco Intersight
E. Add a trusted OAuth token to Cisco Intersight

Selected Answer: BC