350-601: Implementing and Operating Cisco Data Center Core Technologies (DCCOR)

Question #: 1
Topic #: 1
DRAG DROP –
An engineer is implementing NetFlow on a Cisco Nexus 7000 Series Switch.
Drag and drop the NetFlow commands from the left into the correct order they must be entered on the right.
Select and Place:

Suggestion Answer:

Question #: 2
Topic #: 1
Which virtual MAC address is the default for HSRP version 2 group 10?

A. 0000.5E00.0110
B. 0000.0C9F.F00A
C. 3784.0898.1C0A
D. 0000.0C9F.F010

Selected Answer: B

Question #: 3
Topic #: 1
Refer to the exhibit.

Which statement about the ERSPAN configuration in this environment is true?

A. The session number of the source of ERSPAN spanned traffic must have a session ID of 47 for the traffic analyzer to receive the traffic.
B. Host B is the source of ERSPAN spanned traffic and host A is the traffic analyzer.
C. The session number of the source of ERSPAN spanned traffic must have a session ID of 48 for the traffic analyzer to receive the traffic.
D. Host A is the source of ERSPAN spanned traffic and host B is the traffic analyzer.

Selected Answer: D

Question #: 4
Topic #: 1
Refer to the exhibit.

Which two statements about the routing table of the leaf switch are true? (Choose two.)

A. 10.20.1.0/24 is a BD subnet in ACI.
B. The next hop 10.0.1.14 for route 172.16.99.0/24 is the TEP address of a border leaf in ACI.
C. 172.16.100.0/24 is a BD subnet in ACI.
D. The next hop 10.1.168.95 for route 172.16.100.0/24 is the TEP address of a border leaf in ACI.
E. The next hop 10.0.8.65 for route 10.20.1.0/24 is the TEP address of a border leaf in ACI.

Selected Answer: AD

Question #: 5
Topic #: 1
Which mroute state is created when Bidirectional PIM is deployed at a site?

A. *,G
B. MVPN Type-6
C. MVPN Type-7
D. S,G

Selected Answer: A

Question #: 6
Topic #: 1
Refer to the exhibit.

Which statement about the default gateway configuration of the vPC is true?

A. Either switch can act as the active default gateway.
B. N7K-1 acts as the default gateway for all traffic.
C. N7K-2 forwards traffic that is destined for the default gateway by using the peer link.
D. N7K-2 acts as the default gateway for all traffic.

Selected Answer: A

Question #: 7
Topic #: 1
Refer to the exhibit.

What must be connected to clear the HA NOT READY status?

A. Layer 1-Layer 2 ports
B. server chassis
C. management ports
D. network uplinks

Selected Answer: B

Question #: 8
Topic #: 1
A small remote office is set to connect to the regional hub site via NSSA ASBR.
Which type of LSA is sent to the remote office OSPF area?

A. type 7 LSA
B. type 1 LSA
C. type 5 LSA
D. type 3 LSA

Selected Answer: A

Question #: 9
Topic #: 1
Refer to the exhibit.

The STP priority of N7K-1 and N7K-2 are the lowest in the network.
Which statement describes STP on the vPC?

A. N7K-1 and N7K-2 appear as a single STP root.
B. N7K-1 appears as the STP root.
C. N7K-1 preempts N7K-2 as the STP root.
D. N7K-2 appears as the STP root.

Selected Answer: A

Question #: 10
Topic #: 1
The engineer must configure SPAN on a Cisco Nexus 5000 Series Switch to get a capture of the traffic from these applications for an in-depth packet analysis.
Which two SPAN characteristics must be considered? (Choose two.)

A. SPAN source ports can be monitored in multiple SPAN sessions.
B. The Ethernet, FC, vFC, port channel, SAN port channel can be used as SPAN source ports.
C. A SPAN source port cannot be a destination SPAN port.
D. Only Ethernet, FC, vFC, port channel port types can be used as SPAN source ports.
E. The rx/tx option is available for VLAN or VSAN SPAN sessions.

Selected Answer: BC

Question #: 11
Topic #: 1
Refer to the exhibit.

What is configured as a result of running these commands?

A. loose unicast RPF
B. strict unicast RPF
C. IP Source Guard
D. reverse lookup for outbound packets

Selected Answer: D

Question #: 12
Topic #: 1
A customer has a requirement to deploy a cloud service and needs to have full control over the underlying OS, data and applications.
Which cloud model meets this requirement?

A. MaaS
B. PaaS
C. SaaS
D. IaaS

Selected Answer: B

Question #: 13
Topic #: 1
Refer to the exhibit.

A flapping link issue has been reported on the vPC keepalive link. A packet capture has been activated on the Cisco Nexus switch.
What is the destination IP address of the vPC keepalive packets that are sent by the switch?

A. 192.168.254.4
B. 192.168.254.1
C. 192.168.254.2
D. 239.255.70.83

Selected Answer: A

Question #: 14
Topic #: 1
Due to a major version change, an engineer must perform a software upgrade on a Cisco Nexus Series switch.
Which two technologies should be implemented to reduce disruptions to the network during the upgrade? (Choose two.)

A. vPC
B. HSRP
C. VDC
D. MLAG
E. PAgP

Selected Answer: AB

Question #: 15
Topic #: 1
Refer to the exhibit.

What is the result of running the command presented?

A. Multicast traffic forwarding is suspended.
B. MRIB is flushed.
C. The PIM database is deleted.
D. PIM join messages are suspended.

Selected Answer: C

Question #: 16
Topic #: 1
Refer to the exhibit.

What is the reason the system-fm-vrrp checkpoint was created?

A. The VRRP process crashed and the checkpoint was automatically created.
B. The VRRP service restarted and the checkpoint was automatically created.
C. The network administrator manually created it.
D. The VRRP-enabled feature has been disabled.

Selected Answer: D

Question #: 17
Topic #: 1
What are two capabilities of the Cisco Network Assurance Engine? (Choose two.)

A. It validates that devices comply with network security policies.
B. It predicts the impact of changes to the network.
C. It predicts the network load on a data center.
D. It ensures that network performance meets an SLA.
E. It verifies the speed of network packet flows by using telemetry.

Selected Answer: AB

Question #: 18
Topic #: 1
What is an advantage of streaming telemetry over SNMP?

A. on-change traps sent to a receiver
B. periodic push-based subscription messages
C. periodic polling of the device status
D. MD5-based authentication on polling

Selected Answer: B

Question #: 19
Topic #: 1
APIC EPG Resolution Immediacy is set to “Immediate”.
Which statement is true about the Deployment Immediacy for VMM domains associated to EPGs?

A. If “On demand” is selected, the policy is programmed in the hardware only when the first packet is received through the data path.
B. If “Immediate” is selected, the policy is programmed in the hardware as soon as the leaf is booted.
C. The “Immediate” and “On demand” options require a port group to be created on the VDS.
D. If “On demand” is selected, the policy is programmed in the hardware only when the APIC detects a VM created in the EPG.

Selected Answer: A

Question #: 20
Topic #: 1
Refer to the exhibit. All switches are configured with the default OSPF priority. Which configuration should be applied to ensure that the SW2 Cisco Nexus switch controls the LSA floods and advertises the network to the remaining nodes in the OSPFv2 area?

A. SW2# configure terminal SW2 (config)# interface ethernet 1/1 SW2 (config-if)# ip ospf priority 255
B. SW2# configure terminal SW2 (config)# interface ethernet 1/1 SW2 (config-if)# ip ospf priority 1
C. SW2# configure terminal SW2 (config)# router ospf 1 SW2 (config-router)# router-id 10.10.10.22
D. SW2# configure terminal SW2 (config)# interface ethernet 1/1 SW2 (config-if)# ip ospf priority 0

Selected Answer: A

Question #: 21
Topic #: 1
DRAG DROP –

Refer to the exhibit. In a bidirectional PIM network using Phantom RP as an RP redundancy mechanism, two Cisco NX-OS routers have these requirements:
✑ R1 must be the active RP.
✑ R2 must be the backup RP that is used only if R1 is not reachable.
Drag and drop the configuration steps to complete the configuration for Router 2. Not all configuration steps are used.
Select and Place:

Suggestion Answer:

Question #: 22
Topic #: 1
An engineer must configure a Nexus 7000 series switch for HSRP on VLAN 100. When fully functional, the router must be the active master. Which set of commands must be used to implement the scenario?

A. feature hsrp interface vlan100 ip address 10.1.1.2 255.255.255.0 priority 255 preempt hsrp version 2 hsrp 1000 ip 10.1.1.1
B. feature-set hsrp interface vlan100 ip address 10.1.1.2 255.255.255.0 priority 20 preempt hsrp version 2 hsrp 1000 ip 10.1.1.1
C. feature-set hsrp interface vlan100 ip address 10.1.1.2 255.255.255.0 priority 80 preempt hsrp version 2 hsrp 1000 ip 10.1.1.1
D. feature hsrp interface vlan100 ip address 10.1.1.2 255.255.255.0 priority 240 preempt hsrp version 2 hsrp 1000 ip 10.1.1.1

Selected Answer: A

Question #: 23
Topic #: 1
Which MAC address is an HSRP version 2?

A. 3842.4250.0000
B. 0000.0C07.AC1H
C. 0000.0C9F.F0C8
D. 0100.5E7F.FFFF

Selected Answer: C

Question #: 24
Topic #: 1
Refer to the exhibit. Which VLANs are capable to be assigned on vPC interfaces?

A. 100-102
B. 100-103
C. 100-104
D. 100-105

Selected Answer: D

Question #: 25
Topic #: 1
An engineer need to implement a solution that prevents loops from occurring accidentally by connecting a switch to interface Ethernet1/1. The port is designated to be used for host connectivity. Which configuration should be implemented?

A. switch# configure terminal switch(config)# interface Ethernet1/1 switch(config-if)# spanning-tree bpduguard enable
B. switch# configure terminal switch(config)# interface Ethernet1/1 switch(config-if)# spanning-tree guard loop
C. switch# configure terminal switch(config)# interface Ethernet1/1 switch(config-if)# spanning-tree loopguard default
D. switch# configure terminal switch(config)# interface Ethernet1/1 switch(config-if)# spanning-tree bpdufilter enable

Selected Answer: A

Question #: 26
Topic #: 1
A network engineer repeatedly saves a configuration on Catalyst switches to NVRAM using the write memory command. Which action should be taken to implement the same action on Nexus switches?

A. Use the alias command to use the write memory command.
B. Use the wri command to use the copy running-config startup-config command.
C. Use the exit command to leave the configuration mode and save the configuration automatically.
D. Use the write memory command to save the configuration.

Selected Answer: A

Question #: 27
Topic #: 1
What occurs when running the command install deactivate while a software maintenance upgrade is performed on a Cisco Nexus 9000 Series switch?

A. The current set of packages is committed.
B. The package features for the line card are disabled.
C. The package is removed from the switch.
D. The current upgrade stops.

Selected Answer: B

Question #: 28
Topic #: 1
An engineer installed a new Nexus switch with the mgm0 interface in vrf management. Connectivity to the rest of the network needs to be tested from the guest shell of the NX-OS. Which command tests connectivity from the guest shell of the NX-OS?

A. [guestshell@guestshell ~]$ dohost ”ping vrf management 173.37.145.84”
B. [guestshell@guestshell ~]$ chvrf management ping 173.37.145.84
C. [guestshell@guestshell ~$ ping 173.37.145.84 vrf management
D. [guestshell@guestshell ~]$ iping vrf management ip 173.37.145.84

Selected Answer: B

Question #: 29
Topic #: 1
A DNS server with IP address 192.168.1.1 is deployed in a data center. A network engineer must configure a Cisco UCS Fabric Interconnect to use this DNS.
Which configuration should be applied?

A. ficl-mgmt-A# scope fabric-interconnect a ficl-mgmt-A /fabric-interconnect # set name 192.168.1.1 ficl-mgmt-A /fabric-interconnect # scope system ficl-mgmt-A /system # commit-buffer
B. ficl-mgmt-A# scope system ficl-mgmt-A /system # create dns 192.168.1.1 ficl-mgmt-A /system* # commit-buffer
C. ficl-mgmt-A# scope fabric-interconnect a ficl-mgmt-A /fabric-interconnect # set name 192.168.1.1 ficl-mgmt-A /fabric-interconnect* # commit-buffer
D. ficl-mgmt-A# scope system ficl-mgmt-A /system # scope services ficl-mgmt-A /system/services # create dns 192.168.1.1 ficl-mgmt-A /system/services* # commit-buffer

Selected Answer: D

Question #: 30
Topic #: 1
Refer to the exhibit. An engineer needs to implement a monitoring session that should meet the following requirements:
✑ Monitor traffic from leaf to leaf switches on a Cisco ACI network
✑ Support filtering traffic from Bridge Domain or VRF
Which configuration must be added to meet these requirements?

A. interface eth 1/2 leaf 101
B. application epg epg1 app1
C. interface eth 1/2 switch 101
D. application app1 epg epg1

Selected Answer: D

Question #: 31
Topic #: 1
An engineer is implementing OTV on a transport that supports multicast. The solution needs to meet the following requirements:
✑ Establish adjacency to the remote peer by using multicast.
Enable OTV advertisements for VLAN 100 to the other site.

Which two commands should be configured to meet these requirements? (Choose two.)

A. otv extend-vlan 100
B. otv site-vlan 100
C. otv use-adjacency-server 172.27.255.94
D. otv data-group 232.2.2.0/28
E. otv control-group 232.1.1.1

Selected Answer: AE

Question #: 32
Topic #: 1
An engineer needs to create a new user in the local user database on Cisco UCS Fabric Interconnect. The user needs permissions to change the following configuration inside UCS Manager version 3.1:
✑ vNIC and vHBA profiles
✑ Fan speed and power redundancy profile of UCS Manager
Which two roles must be assigned to a user to achieve this goal? (Choose two.)

A. facility-manager
B. server-equipment
C. operations
D. server-profile
E. server-compute

Selected Answer: AD

Question #: 33
Topic #: 1
Refer to the exhibit. Cisco Fabric Services is enabled in the network. Which type of IP address is used by the Cisco Fabric Services protocol?

A. IPv4 multicast address
B. IPv4 unicast address
C. IPv4 gateway address
D. IPv4 anycast address

Selected Answer: A

Question #: 34
Topic #: 1
Refer to the exhibit. A network engineer plans to upgrade the current software images of a Cisco Nexus switch. What is the impact of starting the EPLD upgrade?

A. The switch reboots one time for the new EPLD versions to take effect.
B. The switch reboots multiple times for the new EPLD versions to take effect.
C. The switch skips the EPLD upgrade for each EPLD device of the switch.
D. The switch skips the EPLD upgrade for MIFPGA and proceeds with the other EPLD devices.

Selected Answer: C

Question #: 35
Topic #: 1
Which behavior defines streaming telemetry as a push model in Cisco devices?

A. Events and network changes generate telemetry data
B. Monitoring clients are pulling data from the network to see real-time statistics
C. JSON encoded telemetry data is transported using the gRPC protocol
D. The network devices send data in JSON or GPB format to configure endpoints

Selected Answer: D

Question #: 36
Topic #: 1
After a Cisco Nexus 7000 Series Switch chassis replacement, the administrator discovers that all vPC-enabled LACP port channels are reinitialized. The administrator wants to prevent this issue the next time the chassis is replaced. Which two actions must be taken to meet this requirement before the isolated device is reloaded? (Choose two.)

A. Change the vPC system-priority of the replacement chassis to a higher value than the peer
B. Set the vPC MAC address to a higher value than the peer
C. Configure auto-recovery to the disable state on both peers
D. Set the vPC MAC address to a lower value than the peer
E. Change the vPC system-priority of the replacement chassis to a lower value than the peer

Selected Answer: AD

Question #: 37
Topic #: 1
An engineer performs a set of configuration changes for the vPC domain using Session Manager. Which two commands are used to verify the configuration and apply the device changes when no errors are returned? (Choose two.)

A. commit
B. verify
C. apply
D. checkpoint
E. write

Selected Answer: AB

Question #: 38
Topic #: 1
Refer to the exhibit. An engineer must monitor all LAN traffic on Fabric A from a blade server. Which source should be configured in the test-span monitor session to complete this task?

A. all uplink FCoE ports
B. all vNICs from the service profile that correspond to this server
C. all uplink Ethernet ports
D. all vHBAs from the service profile that correspond to this server

Selected Answer: B

Question #: 39
Topic #: 1
An engineer configured an environment that contains the vPC and non-vPC switches. However, it was noticed that the downstream non-vPC switches do not receive the same STP bridge ID from the upstream vPC switch peers. Which vPC feature must be implemented to ensure that vPC and non-vPC switches receive the same STP bridge ID from the upstream vPC switch peers?

A. vpc local role-priority 4000
B. peer-switch
C. system-mac 0123.4567.89ab
D. peer-gateway

Selected Answer: B

Question #: 40
Topic #: 1
A network architect wants to propose a scalable network monitoring solution in which data is repeatedly acquired from network devices. The solution must use a push model and provide close to real-time access to operational data. Which technology must be used to meet these requirements?

A. CLI-based scripting
B. logging
C. SNMPv3
D. streaming telemetry

Selected Answer: D

Question #: 41
Topic #: 1
A customer needs a tool to take advantage of the CI/CD model to streamline its operations and optimize cost. The customer wants to integrate the solution with the Cisco products it currently uses, including Cisco ACI networking and Cisco UCS Series servers. The solution should also provide on-premises Kubernetes and
AppDynamics performance monitoring. Because of the security requirements, the solution should not install a local client on products under management. Which orchestration solution meets these requirements?

A. Cisco UCS Director
B. Cisco CloudCenter
C. Cisco APIC
D. Cisco DCNM

Selected Answer: A

Question #: 42
Topic #: 1
A customer wants to offload some of its order processing to a public cloud environment. The customer environment is based on Cisco ACI and uses Puppet with containerized applications. The operations team requires a solution to orchestrate and optimize the cost of the new solution. Which product must be used to meet these requirements?

A. Cisco Workload Optimization Manager
B. Cisco CloudCenter
C. Cisco Intersight
D. Cisco Data Center Network Manager

Selected Answer: A

Question #: 43
Topic #: 1
DRAG DROP –

Refer to the exhibit. Drag and drop each traffic flow type from the left onto the corresponding number on the right. Not all traffic flow types are used.
Select and Place:

Suggestion Answer:

Question #: 44
Topic #: 1
DRAG DROP –
A network engineer is asked to describe the cloud infrastructure models from the perspective of their operation and access to resources. Drag and drop the descriptions from the left onto the appropriate characteristics on the right.
Select and Place:

Suggestion Answer:

Question #: 45
Topic #: 1
A network engineer must perform a backup and restore of the Cisco Nexus 5000 Series Switch configuration. The backup must be made to an external backup server. The only protocol permitted between the Cisco Nexus Series switch and the backup server is UDP. The backup must be used when the current working configuration of the switch gets corrupted. Which set of steps must be taken to meet these requirements?

A. 1. Perform a running-config backup to an SFTP server. 2. Copy backup-config from the SFTP server to the running-config file.
B. 1. Perform a startup-config backup to a TFTP server. 2. Copy backup-config from the backup server to the running-config file.
C. 1. Perform a running-config backup to an SCP server. 2. Copy running-config in the boot flash to the running-config file.
D. 1. Perform a startup-config backup to an FTP server. 2. Copy startup-config in the boot flash to the running-config file.

Selected Answer: B

Question #: 46
Topic #: 1
Refer to the exhibit. Which command is run from the Guest Shell to set the description on the first five interfaces of the Cisco Nexus switch?

A. [guestshell@guestshell ~]$ for x in {1..5}; dohost ג€conf t ; interface eth1/$x ; description Server$xג€;
B. [guestshell@guestshell ~]$ for x in {1..5}; do dohost ג€conf t ; interface eth1/$x ; description Server$xג€; done
C. [guestshell@guestshell ~]$ for x in (1..5); do dohost ג€conf tג€; ג€interface eth1/$xג€ ; ג€description Server$xג€; done
D. [guestshell@guestshell ~]$ for x in (1..5); dohost ג€conf t ; interface eth1/$x ; description Server$xג€;

Selected Answer: B

Question #: 47
Topic #: 1
An engineer must configure multiple EPGs on a single access port in a large Cisco ACI fabric without using VMM integration. The relevant access policies and tenant policies have been created. A single AAEP is used to configure the access ports in the fabric. Which two additional steps must be taken to complete the configuration? (Choose two.)

A. The EPGs must link directly to the corresponding AAEP
B. A contract must be defined between the EPGs
C. The EPGs must be configured as static ports
D. The corresponding bridge domains must be configured in legacy mode
E. The EPGs must be linked to the correct physical domain

Selected Answer: CE

Question #: 48
Topic #: 1
Several production and development database servers exist in the same EPG and IP subnet. The IT security policy is to prevent connections between production and development. Which attribute must be used to assign the servers to different microsegments?

A. data center
B. VM name
C. IP address
D. VMM domain

Selected Answer: C

Question #: 49
Topic #: 1
An environment consists of a Cisco MDS 9000 Series Switch that uses port channels. An engineer must ensure that frames between the source and the destination follow the same links for a specific flow. Subsequent flows are allowed to use a different link. Which load balancing method should be used to accomplish this goal?

A. src-id/dst-id
B. src-dst-oui
C. src-dst-port
D. src-id/dst-id/oxid

Selected Answer: D

Question #: 50
Topic #: 1
Refer to the exhibit. An engineer must monitor ingress traffic from SW1 and SW2 port-channel interfaces from SW3. Which configuration must be implemented to accomplish this goal?

A.
B.
C.
D.

Selected Answer: B

Question #: 51
Topic #: 1
Refer to the exhibit. A host with a source address 10.10.10.10 sends traffic to multicast group 239.1.1.1. How do the vPC switches forward the multicast traffic?

A. If multicast traffic is received on Switch1 over the vPC peer-link, the traffic is dropped
B. If multicast traffic is received on Po10 Switch1, the traffic is forwarded out on Po1 and Po20
C. If multicast traffic is received on Po11 Switch2, the traffic is forwarded out only on Po20
D. If multicast traffic is received on Po11 Switch2, the traffic is dropped.

Selected Answer: D

Question #: 52
Topic #: 1
A network architect must redesign a data center network based on OSPFv2. The network must perform fast reconvergence between directly connected switches.
Which two actions must be taken to meet the requirements? (Choose two.)

A. Set low OSPF hello and DEAD timers.
B. Configure all links on AREA 0.
C. Enable BFD for failure detection.
D. Use OSPF point-to-point links only.
E. Implement a virtual link between the switches.

Selected Answer: CD

Question #: 53
Topic #: 1
Refer to the exhibit. Which configuration ensures that the Cisco Nexus 7000 Series Switches are the primary devices for LACP?

A. N7K_A(config-vpc-domain)# role priority 1 N7K_B(config-vpc-domain )# role priority 2
B. N7K_A(config-vpc-domain)# system-priority 32768 N7K_B(config-vpc-domain)# system-priority 32768
C. N7K_A(config-vpc-domain)# system-priority 100 N7K_B(config-vpc-domain)# system-priority 200
D. N7K_A(config-vpc-domain)# system-priority 4000 N7K_B(config-vpc-domain)# system-priority 4000

Selected Answer: D

Question #: 54
Topic #: 1
Refer to the exhibit. An engineer needs to implement streaming telemetry on a Cisco MDS 9000 Series Switch. The requirement is for the show command data to be collected every 30 seconds and sent to receivers. Which command must be added to the configuration to meet this requirement?

A. snsr-grp 200 sample-interval 30000
B. snsr-grp 200 sample-interval 30
C. sensor-grp 200 sample-period 30
D. sensor-grp 200 sample-period 30000

Selected Answer: A

Question #: 55
Topic #: 1
An engineer must configure OSPF in the data center. The external routes have already been redistributed into OSPF. The network must meet these criteria:
* The data center servers must reach services in the cloud and the services behind the redistributed routes.
* The exit point toward the Internet should be propagated only when there is a dynamically learned default route from the upstream router.
Which feature is required?

A. stubby area
B. totally stubby area
C. default-information originate
D. default-information originate always

Selected Answer: C

Question #: 56
Topic #: 1
An engineer must configure a VXLAN routing on a Cisco Nexus 9000 Series Switch. The engineer requires a solution where all the leaf switches have the same gateway MAC and IP addresses. Which configuration set accomplishes this task?

A. NX9K(config)# fabric forwarding anycast-gateway-mac AA:BB:AA:BB:AA:BB NX9K(config)# interface VLAN-interface-name NX9K(config-if)# vrf member vrf-name NX9K(config-if)# fabric forwarding mode anycast-gateway
B. NX9K(config)# install feature-set fabric NX9K(config)# feature-set fabric NX9K(config)# fabric forwarding anycast-gateway-mac AA:BB:AA:BB:AA:BB NX9K(config)# interface VLAN-interface-name NX9K(config-if)# fabric forwarding mode anycast-gateway
C. NX9K(config)# install feature-set fabric NX9K(config)# feature-set fabric NX9K(config)# fabric forwarding anycast-gateway-mac AA:BB:AA:BB:AA:BB NX9K(config)# interface VLAN-interface-name NX9K(config-if)# vrf member vrf-name NX9K(config-if)# fabric forwarding mode anycast-gateway
D. NX9K(config)# fabric forwarding anycast-gateway-mac AA:BB:AA:BB:AA:BB NX9K(config)# interface VLAN-interface-name NX9K(config-if)# fabric forwarding mode anycast-gateway

Selected Answer: A

Question #: 57
Topic #: 1
An engineer implements an ACI fabric and must implement microsegmentation of endpoints within the same IP subnet using a network-based attribute. The attribute mapping must allow IP subnet independence. Which attribute must be selected?

A. IP
B. tag
C. custom
D. MAC address

Selected Answer: D

Question #: 58
Topic #: 1
What is a characteristic of the install all command on the Cisco Nexus Series Switch?

A. automatically checks the image integrity
B. continues the upgrade process if any step in the sequence fails
C. upgrades only certain modules
D. impacts data plane traffic

Selected Answer: A

Question #: 59
Topic #: 1
DRAG DROP –
An engineer must configure the HSRP protocol to implement redundancy using two Cisco Nexus Series Switches, in addition, me HSRP must meet these requirements:
* switch1 must retain the primary role if switch2 goes offline.
* switch1 must retain the primary role until normal conditions are restored.
* switch1 and switch2 must ensure that the routing tables are converged before taking the active role.
* switch2 must retain the primary role if the default gateway is not reachable.
Drag and drop the configuration commands from the right to the left to meet the requirements. The commands are used more than once. Not all commands are used.
Select and Place:

Suggestion Answer:

Question #: 60
Topic #: 1
Refer to the exhibit. During a vPC peer switch reload, there is packet loss between the server and the router. Which action must be taken to prevent this behavior during future reloads?

A. Set the routed uplink ports of the Cisco Nexus peers as orphans.
B. Increase the vPC delay restore timer.
C. Disable vPC ARP synchronize on the vPC peers.
D. Decrease the OSPF hello and dead interval timers.

Selected Answer: B